Gridworx - Ultra System

Website Login



Login Request

If you do not have login credentials please click here

Typical Conditions

Download List

To View The GridPlanx Downloads Please Login

Ultra

The Gridworx ULTRA system allows for the efficient installation of large format ultra-compact surface panels. Continuous rail anchors are fastened to the back face of panel in parallel rows, via an undercut anchor. These rails interlock with adjacent anchors attached to the substrate. Designed as a “floating mount system”, pitch bolts at the top channel allow for fast, pinpoint leveling.

All of our anchoring systems are designed to be mounted to the building substrate via our standard Thermally Broken Components providing space in the wall for insulation and adjustability.

These mounting systems allow for a precise and far more technical way of mounting wall panels thereby allowing for the introduction of mixed media presentations.

Miami Dade Windload Tested. Four full sized Dekton panels (56”x126”) were installed with the Ultra system on the test lab substrate creating a ten foot by twenty foot wall. This wall was then subjected to a 187 mph wind load. Ultimately the testing facility admitted they could not break the system, shut down the testing and issued a PASSED report. No other system in the market can make this claim.

Continuous support panel dead-load
6' X 12' panels up to 1" thick
6005A aluminum alloy T61 temper
75% minimum recycled content
Undercut Anchor
Mechanical Kerf Anchor & Gridworx Mechanical Kerf Lock Washer
Precise Alignment
Panel thickness range: 12mm - 20mm

Project Examples

rainscreen GridPlanx render rainscreen GridPlanx render rainscreen GridPlanx render rainscreen

Thermally Broken Subframe

A thermal break or thermal barrier is an element of low thermal conductivity placed in an assembly to reduce or prevent the flow of thermal energy between conductive materials.

GRIDWORX strives for the best properties of our materials to provide a thermally efficient, energy-saving product that prevents thermal bridging in structural connections. These thermally broken aspects of our Gridworx mechanical stone cladding system are shown below is a section detail of our ASHRAE 90.1 qualified system including our Gridworx sleeve washer and Thermal Sleeve isolating back plate.

rainscreen GridPlanx

 

Please note in the section detail the item described as, “1/8” Thermal Break - Thermal Shoe.”This component is best described as a plastic footing that functions as an insulator between our aluminum Z Girt and the substrate (typically Dens Glass).This is an impact resistant, high quality extruded component made from ABS SP-9010 plastic. Further, this material is heat resistant.

Thermally broken washer GridPlanxThe second item is referenced as, “Thermal Isolated Sleeve Washers.”This sleeve washer is made from NORYL Resin SE1GFN PPE+PS blend. 30% Glass reinforced Non-brominated, non-chlorinated FR system.

Please note the application of this component (drawing above). This washer is designed to first be placed in the pre-drilled hole in the Z Girt.The smaller diameter ring of this component is designed with wings to secure its stability and correct placement in the pre-drilled hole.The sleeve protrusion between this smaller diameter and the larger diameter ring is designed to isolate the steel fastener; keeping it from making contact with the sides of the Z Girt. The larger diameter ring isolates the head of the fastener from contact with the top of the Z Girt.This explanation should make it easier to follow in conjunction with a careful review of the attached section drawing.

This system was designed and approved by SGH Engineering.With a careful analysis, one will note there is no contact between the metal in the wall cavity and that of the steel studs.This is truly a thermally isolated system.

Make good Better

A proposed building design is demonstrated through building energy simulation to use less energy than a baseline building built to ASHRAE 90.1 specifications. All building components must be qualified by individual testing.Gridworx worked closely withSimpson Gumpertz & Heger, an independent engineering firm, in the development of this system. It was deemed to meet or exceed performance standards in Thermal Performance, Air Barrier Performance and Condensation Potential.

Thermally broken GridPlanx

GRIDWORX is a ventilated, back drop rainscreen cladding system. It is a comprehensive system unlike none other.Gridworx consists of our patented contemporarily designed aluminum channels, choices of hundreds of natural stone and man made cladding materials, in-house architectural support, independent third party engineering and state of the art sales support.

• Thermally broken Ventilated Backdrop Rainscreen System ( VRS )
• Non combustible construction
• Adjustable for subwall misalignment
• Cladding joints not tied to stud locations – design freedom
• Easy construction, cost effective
• Suitable for weather barrier (as required by ASHRAE Standard)
• Suits all structures; steel stud, block, concrete
• Extremely versatile grid can support large format panels 3200mm. x 1440mm.
• Traditional installation practices, no training needed
• Made in America

GRIDWORX is committed to providing contemporary construction techniques combined with current modern day materials that make the Gridworx system the best stone installation method in the world.